Safety Grip:
 GT 900  Anti-Slip Coating

Features:

- Anti-Slip finish
- Seamless 
- Impact Resistant 
- Chemical Resistant 
- Minimal Odor during installation 
- Quick installation 
- Economical Price

Benefits:

  • Provides safe work environment
  • Monolithic, joint less installation
  • Reduces maintenance costs
  • Can be installed in most environments
  • Reduced down time for application
  • Excellent return on investment
I.     DESCRIPTION
GT900 is a general purpose, two-component anti-slip coating for application in areas that require a lower profile.  The system is ideal for pedestrian traffic and light rolling traffic.  GT 900 was developed for use in light commercial applications to provide a durable, safe profile.  The system is formulated to provide light to moderate chemical resistance, excellent impact resistance and good color stability.

II.   PRODUCT USES
GT900 is designed to be installed on concrete, metal, or wood.  The system provides protection from slips and falls in a variety of applications.  This product is ideal for docks, ramps, walkways, pool decks, natatoriums, stadiums, or garages.

III.  PRODUCT DATA
Coefficient of Friction                   Dry 0.90 Wet 0.85
Compressive Strength (ASTM C-579)             11,000 psi
Tensile Strength (ASTM D -638)                 3,500 psi
Flexural Strength (ASTM C-580)                 4,000 psi
Shore D Hardness (ASTM D-2240)                       90 
Volume solids                                                    90% 
Pot Life                                                      30 minutes           
Light traffic                                    10 hours @ 80º          
Heavy traffic                                  16 hours @ 80º
Coverage                           50-60 square feet/gallon

IV.    STANDARD COLORS
Tile Red, Black, Deck Gray, Silver Ghost, Tan, Safety Yellow

Custom colors are available and subject to minimum order requirements.

V.   CHEMICAL RESISTANCE
GT900 is fire retardant in its cured state.

GT   900 is resistant to acids, alkalis, solvents, grease, oil, salt water,
detergents, alcohol, diesel fuel, gasoline, jet fuels, and hydraulic fluids. 
Refer to Safety-Grip Chemical Resistance Table for detailed information.

VI.  INSTALLATION PROCEDURE

GT900can be applied to any clean, dry surface.  Remove all paint, construction contaminants, rust, and mill scale from metal or concrete surfaces.  Concrete shall have a profile of CSP-3 to CSP-5 meeting ICRI (International Concrete Repair Institute) guidelines for concrete coatings. Steel shall be prepared to SSPC-SP10 standards. (See Surface Preparation Guidelines)  

Pre-mix Component A with a mechanical mixer making sure that any settlement has been re-dispersed.

Apply only when air and surface temperatures are between 50º and 100º F and surface is at least 5º above the dew point. 

Depending upon substrate use recommended Safety-Grip primer. 

Pour all contents of GT900 Hardener (Component B) into Component A.  Mix thoroughly for 3 minutes until Hardener (Component B) is totally incorporated.  

Pour all mixed contents of GT900 on the surface in a ribbon 6 inches wide.  Use a Safety-Grip  phenolic core roller.  Install material by rolling in one direction only.  Pull material toward you in slow straight strokes with moderate pressure.  DO NOT OVER ROLL.  

Do not thin material.

Allow to cure.  Curing time will be affected by low temperatures and high humidity.

VII.   SURFACE MAINTENANCE
Maintain a clean surface to ensure that the anti-slip safety performance of GT900 be maximized.  Safety-Grip recommends using a non-ionic, free-rinsing detergent using a scrub brush to remove contaminants.  Rinse with clean water and allow to dry. Periodic touch up may be necessary in heavy traffic areas.
VIII.   PERSONAL PROTECTION
EYE PROTECTION All personnel should be required to wear Safety goggles. 
SKIN PROTECTION Utilize rubber gloves, boots, and full length clothing.   

In case of skin contact, wash thoroughly with soap and water.  Remove and discard contaminated clothing.  If skin irritation occurs, contact a physician immediately.    

Maintain a portable eye wash fountain or a clean source of potable water in the immediate work area.  

In case of eye contact, flush with water for a minimum of 15 minutes and seek aid at a medical center for treatment
IX.   SAFETY/HANDLING

Store all materials in original tightly closed containers away from sources of heat, flame and sparks.  Allow no smoking in areas of use or storage.  Use non-sparking explosion proof equipment.  Use only in well ventilated areas.  Supply a positive flow of fresh air when working in confined spaces.


Protect product from freezing and excessive heat.

Minimum shelf life is 5 years in original unopened containers.

Store in a dry area at temperatures between 50º and 90º F.

The information presented herein is believed to be accurate and is presented in good faith for the benefit of the customer. RiTE-TEK, Inc., however, expressly declares that there is no guarantee of result to be obtained by the Buyer. LIMITED WARRANTY: RiTE-TEK, Inc. WARRANTS TO THE ORIGINAL PURCHASER OF ITS PRODUCTS THAT SUCH PRODUCTS MEET THE SPECIFICATIONS CONTAINED HEREIN. NO WARRANTY, EXPRESS OR IMPLIED, OF MERCHANTABILITY OR SUITABLILITY FOR A PARTICULAR PURPOSE AND/OR ANY OTHER WARRANTY IS GIVEN. The obligation of RiTE-TEK, Inc. under this warranty is limited to the replacement of any product which we sell, which may be proven detective under normal use and service within one year of the date of sale. IN NO EVENT SHALL RiTE-TEK, Inc. BE HELD LIABLE FOR ANY CONSEQUENTIAL DAMAGES. 101191